> Terms of Use     

HOME PRODUCTS TRACEABILITY Friendly LINK OVERSEAS AGENCY

HOME > PRODUCT Top > Jont Detector / Wire-breaking Detector


Joint Detector / Wire-breaking Detector

  • IDS Series are most recommended as a Joint detector, but ID Series (Low cost type) are also available for several applications.
  • IDS/ID Series are also available for detection of wire-breaking. CDD-15 is availble for detection of extra fine wire-breaking.

Jont Detector / Wire-breaking Detector -- Specifications


[S]:Sensor、[C]:Controller
Method Proximity type
induction voltage
sensing
Through type
eddy-current loss
sensing
Through type
eddy-current
loss sensing by
bridge circuit
[High sensitivity]
Through type
eddy-current
loss sensing by
bridge circuit
CAD file
(Sensor)
dxf dxf dxf dxf dxf dxf dxf dxf dxf dxf dxf
pdf pdf pdf pdf pdf pdf pdf pdf pdf pdf pdf
Model [S] ID-3L ID-5 ID-8 ID-15 ID-30 ID-50 ID-90 IDS-24 IDS-60 IDS-100 IDX-06
[C] ID-1001 IDS-501 IDX-701
CAD file
(Controller)
-- dxf dxf dxf
pdf pdf pdf
photo Go Go Go Go
[S]Outside
dimension
[mm]
W 30 22 30 38 50 70 110 74 150 201 66
H 30 52 65 80 90 125 175 53.2 113.2 160 47.2
D 22 7 8 10 10 25 38 76 120 124 51
Through hole
dia.(mm)
(Distance:15) 5 8 15 25.5 50 90 24 60 100
6
[C]Outside
dimension

(W * H * D[mm])
120 * 100 * 55 150 * 120 * 75 160 * 150 * 90 140 * 137 * 101
Power supply AC100V 50/60Hz AC100/200V 50/60Hz (With power on monitor)
Power consumption 2VA 3VA 5VA Less than 12VA
Detectiong output Red LED on, One-shot 1a-contact(0.5sec)
Signal monitor Non Bargraph LED display
Sensitivity
adjustment
Single turn volume 10 turns dial 10 truns dial
& 5 step switch
10 truns dial
& vibration of wire correction
Ambient condition Temperature:0 - 50 degree centigrade, Humidity:35 - 85%RH(No condensation)
Feature * For less than
10mm dia. objects
* For magnetic
substance
* Not available for
copper material
* Not available for
shielded cable
* Necessary
attentionto
sensing area
* Abundant sensor variations
* Available for all metal material
* Available for torsion & alloyed junction
* Not recommendable to shielded cable
* Necesssary attention to vibration of wire
* Available for metal material
 (Magnetic substance)
* Available for 
 torsion & alloyed junction
* Also available for 
 shieled cable
* Not so necessary attention  to small vibration of wire
* Available for all metal      material
* Available for 
 torsion & alloyed junction
* Also available for 
 shieled cable
* Not so necessary attention  to small vibration of wire

Joint detectors are also available for Wire-breaking detecting too, and especially, CDD-15 is availble for detection of extra fine wire-breaking. The following teble is comparison between ID-1001/ID-15 and CDD-15.* Necesssary attention to under 15mm breaking length

Type CDD-15
Method Through type capacitance sensing
Sesor outside dimension
(W * H * D[mm])
52 * 49 * 30
Controller outside dimension
(W * H * D[mm])
97 * 131 * 50
Through hole dia. 15mm
Power supply AC100/200V 50/60Hz 4VA
Power on monitor NG
Detecting object Only for single conductor wire,
More than 0.75mm2 area,
For more than 0.165mm as Covered cable dia.
Detecting output Red LED on, One-shot 1a-contact(0.5sec)
Signal monitor Non
Sensitivity adjustment Non
Ambient Temperature 1 - 70 degree centigrage
Feature * Only for Extra fine single conductor wire
* Not so necessary attention to small vibration of wire

[Go to top of this page]

[Back]